Rosemount 848T Spécifications Page 124
- Page / 136
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
114
Reference Manual
00809-0100-4697, Rev GA
Appendix D: Function Blocks
November 2014
Function Blocks
6 BLOCK_ERR None This parameter reflects the error status associated with
the hardware or software components associated with
a block. It is a bit string, so that multiple errors may
be shown.
7 OUT OUT_RANGE The primary analog value calculated as a result of
executing the function block.
8 OUT_RANGE EU of OUT The engineering units code to be used in displaying the
OUT parameter and parameters which have the same
scaling as OUT.
9 GRANT_DENY None Options for controlling access of host computers and
local control panels to operating, tuning, and alarm
parameters of the block. Not used by device.
10 STATUS_OPTS None Allows the user to select options for status handling and
processing.
11,1 2,
13, 14,
25, 26,
27, 28
IN_(1, 2, 3, 4,
5, 6, 7, 8)
Determined
by source
A connection input from another block
15, 16,
17, 18,
29, 30,
31, 32
DISABLE_(1,
2, 3, 4, 5, 6, 7,
8)
None A connection from another block that disables the
associated input from the selection.
19 SELECT_TYPE None Specifies input selection method. Methods available
include: First Good, Minimum, Maximum, Middle,
Average, or Hot Backup.
20 MIN_GOOD None The minimum number of good inputs.
21 SELECTED None The selected input number (1 to 8) or the number of
input used for the average output.
22 OP_SELECT None Overrides the algorithm to select 1 of the 8 inputs
regardless of the selection type.
23 UPDATE_EVT None This alert is generated by any change to the static data
24 BLOCK_ALM None The block alarm is used for all configuration, hardware,
connection failure, or system problems in the block.
The cause of the alert is entered in the subcode field.
The first alert to become active will set the Active status
in the Status parameter. As soon as the Unreported
status is cleared by the alert reporting task, another
block may be reported without clearing the Active
status, if the subcode has changed.
33 AVG_USE None Number of parameters to use in the averaging
calculation. For example, if AVG_USE is 4 and the
number of connected inputs is 6, then the highest and
lowest values would be dropped prior to calculating the
average. If AVG_USE is 2 and the number of connected
inputs is 7, then the two highest and lowest values
would be dropped prior to calculating the average and
the average would be based on the middle three
inputs.
34 ALARM_SUM None The current alert status, unacknowledged states, and
disabled states of the alarms associated with the
function block.
35 ACK_OPTION None Used to set automatic acknowledgment of alarms.
Table D-6. Input Selector Function Block Parameters
Number Parameter Units Description
- Transmitter with FOUNDATION 1
- fieldbus 1
- Transmitter with F 3
- Title Page 4
- 1Section 1: Introduction 5
- 2Section 2: Installation 5
- 3Section 3: Configuration 5
- AAppendix A: Reference Data 6
- DAppendix D: Function Blocks 8
- Section 1 Introduction 9
- 00809-0100-4697, Rev GA 10
- November 2014 10
- OUNDATION fieldbus Technology 10
- 1.3 Service support 11
- Section 1: Introduction 12
- Introduction 12
- Section 2 Installation 13
- 2-in. screws 14
- 2.3 Wiring 16
- RTD or ohm inputs 17
- Analog inputs 17
- 2.4 Grounding 19
- Shielded wire 20
- Grounded thermocouple inputs 21
- Analog device inputs 21
- 2.5 Switches 22
- 2.6 Tagging 22
- Transmitter tag 23
- Sensor tag 23
- 2.7 Installation 24
- 2.7.2 Using conduit entries 25
- Section 2: Installation 26
- Section 3 Configuration 27
- 3.2 Configuration 28
- 3.2.5 Alarms 29
- 3.2.6 Damping 29
- Typical profiling application 31
- OUNDATION fieldbus 33
- Section 3: Configuration 34
- Number Parameter Description 34
- OUNDATION 35
- How to use PlantWeb Alarm 39
- 3.4.3 PlantWeb alerts 40
- MAINT_ALARMS 41
- Advisory alarms 42
- RECOMMENDED_ACTION 43
- FD failed alarms 44
- Configuration 45
- FD CHECK ALARMS 47
- 3.4.7 Transducer blocks 49
- Transducer block errors 50
- Transducer block modes 50
- Automatic (Auto) 51
- Out of Service (OOS) 51
- 4.4.2 Resource block 64
- Appendix A Reference Data 65
- OUNDATION fieldbus parameters 66
- A.3 Function blocks 67
- A.4.1 Stability 68
- A.4.2 Self calibration 68
- A.4.3 Vibration effect 68
- A.4.5 Accuracy 68
- A.4.8 Analog sensors 4–20mA 69
- Reference Data 70
- Examples 71
- A.5 Dimensional drawings 72
- A.5.1 Mounting options 74
- A.6 Ordering information 75
- Approvals 77
- B.3.2 Canada 78
- B.4 Europe 79
- B.5 International 81
- B.5.1 Brazil 83
- B.5.2 China 84
- B.5.3 Japan 86
- B.6 Combinations 87
- B.8 Additional Certifications 88
- B.10 Installation drawings 90
- Product Certificates 91
- Appendix C FOUNDATION 99
- Technology 99
- C.3 Device descriptions 100
- C.4 Block operation 101
- C.5 Network communication 101
- C.5.1 LAS 102
- C.5.2 Addressing 103
- C.5.3 Scheduled transfers 104
- C.5.4 Unscheduled transfers 105
- OUNDATION Fieldbus Technology 106
- Appendix D Function Blocks 107
- Reference Manual 108
- Appendix D: Function Blocks 108
- Table 3-5 on page 11 108
- D.1.1 Functionality 110
- Filtering 111
- Signal conversion 111
- Indirect 111
- Indirect square root 112
- Block errors 112
- Alarm detection 113
- Status handling 114
- Advanced features 114
- Application information 114
- D.2.1 Functionality 118
- D.3.1 Functionality 125
- Block execution 127
- AVG_USE = 6 129
- Numerics 131
Produits connexes et manuels pour Mesure, test et contrôle Rosemount 848T
(36 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.030 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels